- 1 What do you use a chorus pedal for?
- 2 What songs use a chorus pedal?
- 3 Do I really need a chorus pedal?
- 4 Can you use chorus with distortion?
- 5 What goes first chorus or distortion?
- 6 What comes first phaser or chorus?
- 7 What songs use a flanger?
- 8 What songs use reverb?
- 9 What is the difference between distortion and fuzz?
- 10 What is the difference between delay and chorus?
- 11 Where should a tremolo pedal go?
- 12 How do you use the chorus effect?
- 13 How do you make distortion sound good?
- 14 How do you mix distortion?
What do you use a chorus pedal for?
A chorus pedal is a great way to create thicker sounds from a single signal. By taking your source signal, doubling it and setting the second signal slightly out of tune and time with the first, a chorus pedal can create the sound of two instruments playing simultaneously.
What songs use a chorus pedal?
Table of Contents show
- Come As You Are – Nirvana.
- Pull Me Under – Dream Theater.
- Welcome Home (Sanitarium) – Metallica.
- Purple Rain – Prince.
- Paradise City – Guns ‘n’ Roses.
- Getting the Most out of a Chorus Pedal.
Do I really need a chorus pedal?
No one really “needs” any pedals. If you love chorus, then get one. Variety makes the world go round.
Can you use chorus with distortion?
Yes, the chorus pedal can be used to fatten and thicken up a distorted tone, but if you use a distortion heavy sound, the chorus will just muddy up your tone and you’ll get lost in the mix.
What goes first chorus or distortion?
OTOH, a chorus is actually linear (or approximately linear), so technically it really makes sense to put it after distortion: chorus after distortion actually gives almost the same result as you’d get by putting each individual chorus voice through a seperate distortion unit.
What comes first phaser or chorus?
Traditionally you want your phaser first, then flanger and chorus in whatever order after that. But there’s nothing wrong with putting your chorus first and phaser last. That’s how neat sounds get created. I’ve had my chorus before my phaser for years.
What songs use a flanger?
7 Songs That Show Off Flangers & Phasers
- 2. ” Head Over Heels” by Tears for Fears – This is one of the truest, cleanest, most exciting flanger effects ever put on tape.
- 4. ” Just The Way You Are” by Billy Joel ““ That’s a phaser on the famous Fender Rhodes intro.
- 6. “
What songs use reverb?
8 Songs that Belong in the Reverb Hall of Fame
- King Tubby “Dub You Can Feel”
- Joe Meek “I Hear A New World”
- Led Zeppelin “When The Levee Breaks”
- Grimes “Venus In Fleurs”
- The Drums “Down By The Water”
- Shinedoe “Cosmic”
- Phil Collins “In The Air Tonight”
- Blake Mills “Shed Your Head”
What is the difference between distortion and fuzz?
What Is the Difference Between Overdrive, Distortion, and Fuzz? An overdriven tube amp creates distortion, but in the world of effects pedals, distortion stompboxes tend to be a bit more intense than overdrive stompboxes. Fuzz is a special type of distortion where harmonic overtones dominate the overall sound.
What is the difference between delay and chorus?
Delay is like an echo, repeats the signal after it’s played. Chorus creates harmonious sounds that play in sync with your playing.
Where should a tremolo pedal go?
For most players, the ideal location to place modulation effects—which include phase shifters, flangers, chorus, rotary, tremolo, vibrato and so on—is directly after a compressor and/or overdrive/distortion pedal.
How do you use the chorus effect?
Chorus Effect Techniques Slam the feedback level up to roughly 90%, set a 40ms delay and dial in the chorus rate to about 0.07. Once this is done you can make a huge spike in the chorus depth at the end of the sound to give it an energy discharge.
How do you make distortion sound good?
Note: For this discussion, we will be using the method that is most useful for playing many different types of rock music.
- Step 1: Find A Good Clean Tone.
- Step 2: Find Your Overdrive Tone – Light Distortion.
- Step 3: Find Your Lead Tone – Heavy Distortion.
- Step 4: Unity Gain.
- Step 5: E.Q. or Equalization.
How do you mix distortion?
4 Ways To Bring Your Mix To Life With Distortion
- Warm Up Your Mix With Analogue Modelling Plug-Ins. Running your tracks through analogue modelling compressors and EQs can really do a lot to warm up a sound.
- Add Detail and Clarity to Bass Lines.
- ‘Glue’ Sampled Drums Together.
- Power Up A Weak Vocal.